電工鋼硅鋼片應力退火電工鋼在剪切、內蒙古阿拉善同城沖片和彎曲加工等機械變形作用下，電磁性能將發生劣化。為此進行應力退火，可以使電工鋼的電磁性能恢復至原來水平。應力退火的條件和工藝將根據加工程度、內蒙古阿拉善同城退火爐況等有明顯不同，用戶務必注意如下幾點：(1) 加熱與冷卻速度電磁性能一般不受加熱和冷卻速度的影響，但用戶需確保材料不變形。(2)退火溫度與保溫時間取向電工鋼退火溫度在780-820℃之間較為適宜，為確保退火效果，退火材料應均熱的保持，保溫時間應根據鐵芯形狀、內蒙古阿拉善同城裝爐量等進行調整。(3)防止?jié)B碳與氧化由于滲碳及氧化會使電磁性能劣化，用戶應充分注意爐內氣體，并確保爐內氣體的露點在較低狀態。另外，為防止在退火中發生滲碳，應該在退火前，將鐵芯加工過程中潤滑油脂等有機化合物干凈。同時，為確保退火效果，建議與爐內高溫接觸部分盡量采用低碳含量材料。有害物質限定承諾 寶鋼的取向電工鋼產品符合RoHS、內蒙古阿拉善同城REACH有害物質限定要求。

電工鋼硅鋼片Electrical steel, also known as silicon steel sheet, is an indispensable metal material in the power, electronics, and military industries, and is also the largest functional material in production. It is mainly used as the iron core for various motors, generators, and transformers. Specific total loss (iron loss) is the total power consumed per unit mass of material when the magnetic polarization waveform remains sinusoidal, with a specific peak and frequency. The specific total loss is represented by the symbol P (Jm/f), in W/kg. Example: P1.5/50 represents the specific total loss at a maximum magnetic polarization intensity of 1.5T and a frequency of 50Hz. 3.2 Magnetic Polarization Q/BQB 480-20212 Magnetic polarization intensity refers to the peak magnetic polarization intensity of a specific magnetic field intensity when a sample is subjected to alternating magnetization. Its symbol is J (H), and the unit is T (Tesla). Example: J5000 represents the peak magnetic polarization intensity corresponding to a magnetic field intensity peak of 5000A/m. The material grades in this document are classified based on the nominal maximum specific total loss P1.5/50 (W/kg) at a magnetic polarization strength of 1.5T and a frequency of 50Hz, as well as the nominal thickness of the material. They are further divided into three categories based on product characteristics: ordinary type, stress relief annealing type, and high-efficiency type. Example 1: B35A210 represents a common non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific total loss value P1.5/50 is 2.10W/kg； Example 2: B35AR300 represents a stress relieved annealed non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific total loss value P1.5/50 is 3.00W/kg； Example 3: B35AH230 represents an efficient non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific loss value P1.5/50 is 2.30W/kg. Example 4: 35WW210 represents a normal type WW non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific loss value P1.5/50 is 2.10W/kg. Example 5: 35WH230 represents an efficient WH non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific loss value P1.5/50 is 2.30W/kg. The classification and code of insulation coatings shall comply with the provisions of Table 2. Table 2 Classification and Code of Insulation Coatings Type Code Characteristics of Insulation Coatings Semi organic Thin Coating A Improves Punching Performance and Has Good Weldability Semi organic Thick Coating H has Good Punching Performance and High Interlayer Resistance Semi organic Chromium Free Thin Coating K does not contain chromium and has good weldability Semi organic Chromium Free Thick Coating M does not contain chromium and has good insulation performance Semi organic Chromium Free Extreme Thick Coating J does not contain chromium and has excellent insulation performance Semi organic Chromium Free Ultra Thick Coating L does not contain chromium and has extremely high insulation performance Self adhesive Coating