保養泵的方法：

1、泵注意絕緣電阻，長期擱置不用的或在潮濕環境中使用的電動抽液泵，使用前必須用500伏兆歐表測量繞組的絕緣電阻。
2、泵和電動油桶泵應經常檢查，維修，在檢查時,必須檢查電源線：內接線，插頭，開關是否良好，絕緣電阻是否正常，刷尾座是事松動，換向器與電刷接觸良好，電樞繞級擴定子繞組是否是有適中斷路現象，軸承及轉動零件是否的損壞等等。
3、經常加脂，電動油桶泵為高速運轉，潤滑脂易于揮發，所以必須使軸承處的潤滑能保持清潔，并注意添?yè)Q。         

軟管泵工作原理：
一根內壁光滑，強度可靠的特制橡膠軟管安裝在泵體內部，通過一對壓輥沿著軟管旋轉擠壓，這樣的 旋轉使得介質往一個方向輸送而不會倒流，軟管在輸送介質之后，由被壓扁軟管的自身彈性和側導輪的強制下，軟管恢復原狀，此時，軟管內產生高真空將介質再次吸入管腔，然后介質在隨之而來的壓輥擠壓下從軟管內排出，如此周而復始，介質不斷的被吸入和排出。目前產品使用溫度為≤100℃。根據用戶需要可以開發使用溫度在120℃的軟管泵軟管產品。
Working principle of hose pump:
A special rubber hose with a smooth inner wall and reliable strength is installed inside the pump body. It is rotated and squeezed along the hose by a pair of pressure rollers. This rotation allows the medium to be transported in one direction without flowing back. After that, due to the elasticity of the flattened hose and the force of the side guide wheels, the hose returns to its original state. At this time, a high vacuum is generated in the hose to suck the medium into the lumen again, and then the medium is pressed by the subsequent pressure roller. It is discharged from the hose under the squeeze, and so on and on, the medium is continuously sucked in and discharged. The current product temperature is ≤100 ℃. According to user needs, we can develop hose pump hose products with a temperature of 120 ℃.